For the Golden Egg challenge, I made a warm, woollen coat. The purpose of the coat was to make an over-garment from sources that would be warm, practical and fitting for the period. After using it for half a year I am very satisfied; it is such an easy garment and yet it looks great, is comfortable and versatile. I use it as part of the outfit, when the weather is cold or wet, as a robe when visiting the bathroom early in the mornings, as a picnic blanket…
I drew you a basic pattern outlay if you want to try it out for yourself.
The small gores F1 and B1 are just to save fabric, so the main pieces are 2 fronts, 2 backs and 2 sleeves. If you have a toile or mock-up that works for you, you can use that as a base and then just draw out the lines from the sleeve/neck as I did on the pattern.
The fabric I used was 310 * 150 cm, if you are taller or need a size large or above, consider adding some extra fabrics for lengths and sleeves. You don’t really need as much width as I have, but it will give you a very nice drape and look.
The cut and pattern are based on paintings and what pattern instructions I have found from the period. I think it is a possible take, though I have seen outer garments with S-sleeves, sleeve gores and more intricate patterns and constructions. The side seams can be found in some pictures, as well as in patterns of outer garments from later periods.
When you have cut out the pieces needed, pin/baste and sew the coat together in the following order:
back seam
shoulder seams
side seams
sleeves
insert the sleeves in the coat
hem the coat
put in a closure at the front neck.
I used unbleached, waxed linen thread and a running stitch, folded the seam allowance to one side and fastened it down with whip stitches. The hems were finished with whip stitching too.
I also trimmed the neck and sleeves with fur, since that seems to be common in contemporary art. To avoid dipping the sleeve hems in food, I made the sleeves wide enough to be able to fold the fur inside the sleeves when working- this turned out very practical!
Materials:
The coat is made in warm, thick wool twill, with a rich, deep brown colour that would have been quite expensive to dye. Other good colours could have been walnut brown, red or black.
Linen thread for sewing, since this seems to be common in most finds from the period.
Rabbit fur for trims, because that was the only fur I found that was up to my ethical standards about how you should treat animals (eco, small family garden breeding, killed and tanned in the area without chemicals). White fur to match the paintings. If you don’t want to use fur a folded down hem would do just fine!
The clasp is based on a find from the period and is made in bronze
You can wear the coat loose, or close it with a belt. I often wear it with a belt, as it is more practical. If you want tips on sewing a fur trim on a garment, check out my tutorial on the subject!
Historical sources and why I did a coat
The outer garment could be a dress as well, as there are lots of warm dresses lined with furs or fabric in sources. I chose the coat as I wanted a practical garment, and know from experience that the second layer of wool dress would not be versatile enough for what I needed. The sources I have used are from the second half of the 15th century, in today’s Germany. The Golden Egg outfit is based mainly on the period 1470-1490, but the coat belongs to the end of this period rather than being the “choice of all women”. So now you can decide if you should go for the practical coat or the more common dress when making your outfit!
OLYMPUS DIGITAL CAMERA
Sources: if you want to check out some sources on 15th century clothing, I recommend some of these links:
This is my walk-through on how I made my green 15th c kirtle/dress in wool. It is not a complete tutorial with all details, so if you have never sewn before I recommend starting with a shift or other straight garment. If you want more good sewing tip, you will find many problems addressed in my other tutorials.
This is a common late 15th c middle dress for women, it is quite easy to make, practical and is shown in many different pictures from the period. Your choice of colour, neckline, clasps and other details will make it different, and if you choose a thicker wool fabric it will work as an overdress too. The artwork I have used is from 1470-1485.
You will need about 3-4 meters of thin wool fabric, I bought mine from Handelsgillet, they have a thin twill fabric that is easy to work with and quite historically accurate for the period. I fell in love with the perfect green colour… And you can see some examples of green kirtles at the bottom of this blog post and in other artworks from the period. The shade can be achieved with plant dying but is more expensive than a madder red or yellow, and I think it makes a good option for my outfit; a well of burgher from a city.
I lined my dress with prewashed, unbleached linen, but you only need to line the upper body for some stability, and that will need a maximum of 1 meter. I sew my dress by hand, with waxed linen thread. Running stitches for the main seams, back stitches in armholes and sides, and whip stitches for the seam allowances and hems, are all you need. The dress closes with hooks and eyes, be sure to have lots of them!
This is what the model looks like, it is really simple, and if you have a personal toile/mock-up for your upper body you can use that with some small modifications. The front opening should have a slightly curved seam to follow your body, and the closure makes the front pieces lay edge to edge.
Comparing to a supportive kirtle, you need a bit more room now for your bust area, it should be quite loose and lay over your breast, to get the shape of the period. Make a new mock-up in fabric and make the front pieces a bit wider, and try it out.
The sleeves are regular S-sleeves or a sleeve with a curved upper edge and seam under your arm. You can see both from the period, though the S-sleeve seems to be more common. The skirt is made up of 4 pieces in my dress. Here are the pieces I used together with my measures (around 36-38/small European size)
The dotted line on one of the skirt panel indicates a gore to save some fabric, but I wrote out the wrong number of pieces; the left panel is the front and you only need one of them. But this is just one way to create the skirt; you can use more pieces, gores, or just 2 wider parts.
The upper body back piece is whole, you can shape the back in the sides and with the help of the waist seam.
I lost my sketch of the outlay but made another one just to show you. Since I am a rather petite person, I can use the width of the fabric for most outlays, but if you are longer than I am (around 160 cm) you may want to lay the skirt panels out the other way. In this picture the panels are a bit wider in the back than that above, so you only need two. The front is straight or almost straight. Note also that I apparently drafted regular sleeves instead of S-sleeves, but you will get the idea…
After I cut out all the pieces, I basted the dress together to try it out. When happy with the fit and measures, I started to sew all the seams by hand. If you keep the correct basting stitches while sewing, you don’t need to pin and can easily work on the sofa, super cosy!
Make the dress in the following order:
Sew the upper body together, front and back pieces, and then sew the sleeves before you insert them in the body.
Sew the skirt panels together, but leave around 20 cm at the top centre front, to be able to put the dress on (the slit shown on the first sketch). I hemmed the body and the skirts upper circle separately, and then attached them to one another with whip stitches. This seam will get a lot of wear, so it is nice to make it twice or use a sturdy thread, like the buttonhole silks or a thicker linen thread, like 35/2.
When the whole dress was assembled together, I put it on my doll to hang out for some days, before I cut and hemmed the skirt and sleeves. If you have a doll, it is really good to leave the dress hanging for a couple of days before hemming, this will make the fabric in the skirt stretch out, and you can cut away excess fabric to make the hem even.
The front with its lining is sewn from the right side, first with basting and then with a seam. To make the front opening and the neckline more durable I added a second row of stitches around.
The hooks and eyes are fastened last. This is what it looks like on the inside, note that I have sewn the hooks and eyes not only in the loops but also at the stems/higher up. This will make your opening lay flat and give that characteristic look at the closure you can see on 15th c paintings.
And finally, some of my favourite artworks that I used during my research. As you can see, they are all green kirtles, of the same models, but with some different cuts, necklines, closures and headwear.
Historically accurate? My main aim with making this outfit was practicality, durability and a dress I would feel comfortable in, based on period clothing. With this said, I aimed to make the dress (and outfit) as historically believable as possible from my means.
The fabric is machine woven and dyed to cut on costs, but the pattern construction, sewing techniques, material and look aims to be close to the dresses from the period. Another modern take is the hooks and eyes, which are machine-made instead of handmade.
I rarely work with metal due to some problem with my joints, but I tried to make a couple of hooks and eyes by hand. It is not hard work, they got quite pretty, but I didn’t make enough of them for a dress.
One thing I did give a lot of thought was the lining. My experience is that lining a skirt with a different material that is sewn down in a slim hemline rarely gives a good result. But I was curious and gave it a try with the method of letting the skirt and skirt lining hang down before cutting and hemming. It worked quite well but gave me a lot more work than leaving the skirt unlined. In artwork, you can often see a lining inside the dresses, and this was a try to make one without adding warmth with another wool layer.
This post is about my work with 15th c dresses for the Golden Egg challenge I do in the SCA, and it will be something like an overview on dresses. If you want pattern outlays and sewing tutorials, check out my tutorial page!
What is really the difference between a kirtle, middle dress, dress, underdress and so on? Not much, except the words. All these can be used for the same garment, depending on the country of origin and the period. A kirtle refers to the main (upper body) garment for both men and women, which should be long (and loose at the hem). A tight-fitting, short garment with the same function is called a jacket or doublet. A kirtle can be both a tunic and a dress. So it is more of a language term than a specific garment.
Dresses are basically what you think it is; long garments (for women in this post) worn in different fashions, styles and materials. The medieval women generally wore several layers of garments, so to better talk about these, they are given different names.
The shift, chemise or underdress is your underwear, usually in bleached or unbleached linen, washed frequently as you would do with modern underwear.
The supportive shift is a sleeveless, tight underwear to support and shape your bust. You can see it in both pictures and as a find (Lengberg). You can wear it on its own under the middle dress, or together with a shift with sleeves.
The kirtle or middle dress is the next layer, often in wool, but also in silk, cotton, velvet or mixes of materials. You can wear this in public, and during the 15th c, it is often tight fitted. The cotehardie? That is french, meaning basically a kirtle but is referred to as a tight fitted 14th c garment for both men and women, often with buttons or lacing.
The dress or overdress is a warm layer worn on top of the first two, during the 15th century it is often loose, with lots of draping fabric. And as expensive as you can afford it. The houppelande? A certain style of overdress, with an opening at the centre front, often elaborate sleeves and lots of fabric in the skirts.
The coat or cloak is a layer of its own, to protect the wearer from the weather (or for symbolic/religious use) or as a fashionable garment. Women and men both wear them and own them in sources, but they don’t seem to be high fashion during the 15th c, more like a practical choice.
OLYMPUS DIGITAL CAMERA
During the 15th century, fashion seems to change quite fast, and you can also see many different styles of dresses in the same picture or geographical area during the same time. If you want to research different kinds of styles yourself, I recommend diving into some artwork for the period. I have two pinterestboards to check out, one about my Golden Egg project here, and another on interesting 15th c clothing here.
I also wrote a post about research and artwork here. I could really go on and on about different models of dresses forever, but to keep it simple I am just going to show you some different examples I have tried to recreate from the 15th c:
For my wardrobe, I opted for the green kirtle, a simple dress with long sleeves, a waist seam and front closure with hooks and eyes. The sleeves can be loose enough to roll up to the elbow, or a tighter version like mine. The front opening continues after the waist for a bit, to make the dress easy to take on and of. Decorative clasps by the front or lacing seem to be options for this style. It also seems like the kind of dress you can wear as both middle or overlayer on your outfit, depending on how you fit it and the choice of material.
But I also got curious and tried out the loose dress model with my dove blue dress, based mainly on a picture from Bohemia. These model can often be seen with a decorative closure at the neck and is held together by a thin belt by the natural waist. The breast can be seen as two individual shapes; you need a supportive shift with separated cups or a modern balconette bra to achieve this look! (or go natural)
Before, I tried to recreate this kirtle with short sleeves and a waist seam with a plaited back, based on some artwork of Weyden. The sleeves have a seam under the arm instead of the more common S-sleeve, the middle back has a seam, and there is a strip of fabric around the neckline, as a way of giving support to the shape. The front of the skirts lay smooth to the upper body, but at the back, there are plaits to add volume and a nice drape to the dress.
The houppelande is such an interesting garment, and I have tutorials about the different pattern and outlay. These are some of the different versions I have made. I really am a fan of this green colour as you may have noticed, and my friends use to joke with me if I don’t wear green at events…
I took some quick pictures to show you how I make my braids for the 15th century outfit. I do not make them to all events, and they end up looking a bit different each time, but this is the basics for the look! (this is not a historically accurate way, but it is one that really works for me during work and camping events so I wanted to share)
You will need:
Longer hair, or hair extensions.
Brush, comb, hair wax (optional), rubber bands or thread, 2 bobby pins.
First, I divide the hair into two sections and brush them out. Then I usually add some natural hair wax to get the hair a bit easier to work with. The hair is pulled to the front, and the braid is a regular 3 strand braid that begins over the ear.
Look at the start of the braid, it is really high up and almost at the front of my hairline:
Braid both sides, finish them off with a small rubber band or thread. I always use rubber bands, because I am lazy…
After this, it is time to fasten up the two braids in loops. I usually do this by pulling a bobby pin through the rubber band, so the pin hangs at the end of the braid. This is the hair from behind; you don’t have to make it perfect, but try to pull the braids tight from behind to avoid the hair falling down your neck.
After that, grab your bobby pin, fold the braid back and put in the bobby pin at the start of your braid. If you have extensions, you can pin it through the base of one of these for extra firmness. Make sure the pin is secure, give it a small “twist” to secure it inside the braid.
Then it should look something like this. The loose hair ends lies against my head, behind the braids and under any cap or veil, I will wear. The bobby pin and rubber band is also hidden. Note the lenght of the braid in different paintings when deciding how long yours should be. I like them to reach the line of my nose, it makes my face look cute.
And from behind
There, all done! I have discovered that the best way to hide the loose hair and the small hairs at the neck is to use a modern, thin hairband in fabric, that I pull over my head and smooth away the hairs with. I didn’t use that this time, and you can use hair spray, wax, bobby pins or whatever you fancy to hold your hair in check.
The result? This is what it looks like when styled with the 15th c great veil.
I actually started to write this in spring 2017, and now more 1,5 year later I finally feel that I can post it. Why did it take such a long time? Because it was a new subject I approached, and I was not confident enough to post something I didn’t really know that much about. But now, looking back, I can see that the post is just right for that moment in my work. It is the first in a long series of try out, and I wanted to show you some part of my learning process.
I’m really in the beginning of reenacting the 15th century, but find both the clothing and the headwear so interesting! One of the things I have learned while trying to do the headwear myself, is that it really is important to look at the details to get the over all look for your outfit.
This is what I came up with for the event my local SCA group had early in the summer. It looks ok, but really only is a lot of linen veils pinned down on top of each other, with a really long one then draping over the head at the end. But this chaotic look actually resembles some of the paintings…
Want to try it for yourself? I start by putting up my hair in braids, and then a Birgitta cap for a secure base. Then I add one or two thin linen veils on top of that, wrapped and pinned to the head like a turban, to get the volume and shape of the headwear. On top of those, I then add a very long veil that is pinned down, and then hangs loosely from one side. This is folded and laid over the head, quite loose. And that is all. I’m yet to learn the best way to put the pins, how many is needed, and most of all; remember how I did the headwear some months later when I want to redo it again.
This weekend we traveled north to visit friends at our old hometown Umeå. The local SCA group had an event, se we had a great weekend with a mix of old and new friends, medieval archery, feasts and a bit of work, since I brought my small shop with me.
Thank you everyone who came by to shop; thanks to your support we get to visit all lovely events!
During Saturday we were outside practicing archery, it was a little below freezing, with a cold wind blowing. I though I brought enough clothing, with a thin woolen dress, a wool jacket, and my brown wool coat, but the wind managed to sneak inside the layers of clothing and I soon became chilled.
This really got me thinking, since I plan to go to medieval Christmas in Visby in the middle of December. Maybe I need to make a warmer coat with a lining and closure at the front? I am also going to bring my hood, better socks, and a woolen layer of underclothing. And woolen veils. Yeah, that will probably do the trick!
Are you going to a medieval or historical event during the winter season too? Here is some tips I have for keeping warm (they were published 4 years ago in a Swedish version then) I also wrote this post in Swedish about keeping warm.
Layers are really nice, and loose layers will create isolation thanks to the air between them.
The choice of materials; silk and wool will warm you even if wet, while cotton and linen will cool you. Wear you wool dress or tunic against your skin, or add a thin modern layer of wool underclothing.
Fur is very warm, even a trim will keep the warm air inside the garments and warm you.
Leather is not warm at all (don’t trust the fantasy movies) but protects against wind if worn over woolen layers.
Do not let the weather chill your skin, protect hands, face and head. You lose lots of warmth from the head, chest and shoulder area, so a hood can make quite the difference! Use it as a way to adjust your temperature; take of when indoors, put on if cold.
Isolate your feet from the ground. Cold ground or wet feet will make you cold. Use woolen socks, and if you have medieval shoes a pair of pattens (wooden soles) will protect you. I often wear modern shoes to winter events to be sure I will stay warm enough.
If standing still in a market something on the ground will help you keep warm; straw, a woolen blanket, a sheepskin, a wooden board. Anything is better than nothing!
Wind chills you down; if it is windy or rainy another layer will help you keep warm, like a thick cloak, coat, shawl or a wool blanket.
As a woman it is the right time to be fashionable; headwear like veils and wimples will keep you warm. Even silk and linen veils will warm you and protect you from winds.
Eat and drink lots to get energy to warm yourself. Tea, hot chocolate, snacks; whatever you fancy!
When going indoors; remove some layers of clothing to get warm, but not too warm. To go in and out without undressing will only chill you further.
Already cold? Go on a brisk walk to make the movement warm you, do a little dance, or just jump up and down. Movement and energy intake (snacks!) makes your body produce heat.
Thats it- with some more planning I think I will do great during this winter!
This is a tutorial with very detailed step-to-step instructions, and I will base other tutorials on this one and simply state “do as in the simple dress tutorial but…” so this is a go-to for many different garments. I call it the simple dress since it is so versatile, the base for so many other garments!
It is also suitable to make men’s kirtle, tunics and coats, just adjust measures and fitting to a male body. Most garments are more difficult to make for women’s bodies since the measures differ more, and therefore you will find more tutorials on my page for women’s clothing.
This is the dress we are going to make. Note that a regular S-sleeve does not have two seams, only one at the back. The reason my dress have two seams in the sleeves are 1. you will learn how to make that for doublets, jackets and 2. I saved fabric that I was short on.
Good tips:
If sewing on a sewing machine, pin from right to left, across the seam, to make it easy to remove the pins while sewing. If sewing by hand, pin along the seamline so as not to get the pins in your hand, or baste the seams before sewing.
When pinning; always lay your pieces on a flat surface (a table or the floor) and work on that while pinning. This will make the work easier, and the seams better.
Basting seams are an easy way to try the fit, size, movement and drape of skirts while sewing. Basting the armhole before sewing makes that seam easier to finish nicely. When you pin/baste together long seams, such as a diagonal cut gore with a straight panel, put the gore (the diagonally cut stretchy part) under the other one, when sewing on a machine the gore will not stretch.
Don’t be afraid to cut out your armhole according to your body. The sleeve should cover your arm, the arm joint, but fit snugly under your arm (in the armpit). A too shallow armhole will make your sleeve hang, but too wide will make movement hard. Experiment on scrap fabric first.
How many gores? Two are enough for undergarments and knee-long kirtles, four or more will give you more width, a smoother and more even fall of fabric and more movement when walking. Regular seam allowance is 1,5 cm. For hems 2 cm. You can pick whatever measure you want between 1 cm-3 cm, just remember what you chose. Seam allowance is mentioned as SA in this post.
Wash and iron your fabric before sewing. The fabric is prepped with chemicals to avoid mould or bugs during the shipping and selling process and could be stretched uneven after the weaving. It will also most likely shrink a little, so this makes you able to wash your clothes after using them.
Start with your measures:
Around your widest part on your upper body(often over the bust).
Length of the garment; from shoulder to hem.
Length of arm; from shoulder-elbow, while bent 90 degrees, to the wrist.
Around your wrist (for tight buttoned sleeves) or around your hand to be able to take on and off the garment.
Create your armhole (if you find this hard; try to measure around a loose shirt or blouse. The armhole should be a bit loose without hanging).
Length from shoulder to natural waist (for women) to hip (for men). This is where I attach the gores.
Draft the pieces you need on a bit of paper. Calculate the measures you need:
Around your widest part of torso: Divide in 2. Add seam allowance: 3 cm/piece. Add some extra for movement: around 6%. Example: around bust: 100 cm. Divide in 2= 50 cm. Add s.a = 53 cm/piece. Add movement = 53 + 6% = around 56 cm. Each piece is now 56 cm wide.
Length of garment; from shoulder to hem. Add seam allowance: 2 cm = hem + 1,5 cm for shoulders. Example: dress should be 140 cm when finished. Length of piece: 143,5 cm.
Length of arm; from shoulder (around elbow while bent 90 degrees) to wrist: Example: 64 cm. Add SA., so sleeve pieces should be 64 +1,5 +2 cm= 67,5 cm. Try on before hemming to adjust the length to your taste.
Around your wrist (for tight buttoned sleeves) or around your hand to be able to take on and off the garment): The narrow part of the sleeve. Check so you can put it on/off. Shape the sleeve to your taste so it fits comfortable around your arm while sewing the sleeve. This is just the starting measure.
Around your armhole (if you find this hard; try to measure around a loose shirt or blouse. The armhole should be a bit loose without hanging). The measure you got is divided into 2, for a measure of the sleeve hole on the front and back piece. Example: around my armhole, I have 56 cm. 56/2=28 cm. Each armhole on the pieces should be no more than 28 cm (measure the curve).
The sleeve base should be 2 cm wider than the complete armhole. 56 cm + 2 cm= 58 cm (measure around the S curve of the arm) add SA: 58 + 3 cm= 61cm is the sleeve base measure.
Length from shoulder to natural waist (for women) to hip (for men). This is where I attach the gores. For example: my measure is 38 cm. From the shoulder, I measure 38 cm and make a line, here is where the gores should be attached on front and back pieces. For gores in the middle back and front, cut a straight line to 1 cm below this measure (39 cm from shoulder) to insert them. Check out my tutorial on how to make these
Length of gores: length of the dress – length from shoulder to waist/hip + 3,5 cm SA. Example: 143,5 cm -38 cm = 105,5 cm + 3,5 cm = 109 cm.
The width of gores depends on what kind of dress you would like to do, your overall size and how much fabric you have. I recommend a measure between 50-80 cm for each gore. A lower-class garment might have narrower gores, a fancy dress wider. If you calculate on a larger size than this example, let the width of the gores follow the other measures. For example: if your circumference around your torso is 20% more, also add 20% width to the gores. This will make sure the dress keep good proportions and all the drape.
When calculating all these measures, draft them out on your pattern pieces to remember them.
Then, draft all the pieces on your fabric with a fabric marker and ruler. Check that you have made all the pieces with the right measurements and that all are drawn onto your fabric before cutting. Mark them with front/back/sleeve/gore.
Cut them out. If I work with linen, silk or brocade that will fray, I sometimes zigzag around all pieces on my sewing machine.
Sew the pieces together in this order:
Shoulder seams
Make the sleeves
Attach the gores to dress front, back, sides
Side seams; front to back and gores so the sides will be completely closed
Sew the sleeves into the armholes
Hemming and adjusting length
Note: This work order goes for both the sewing machine and hand-sewing. When I make a seam I finish it off before starting the next one. That means;
pinning/basting
sewing the pieces together front to front
pressing down the seam allowance on the wrong side (the inside)
cut down the seam allowance on one side
press again, the wider over the cut one
whip stitch the seam allowance down (can also be done when the dress is ready if you want to try the fit during sewing)
The reason to press the seams before sewing another one is that you will have flat and nice looking seams, and it will be easier to make the next one crossing the first. I really recommend you to at least press the seam allowance once, it makes such a difference!
Step-to-step for sewing the dress.
Sleeves:
Pin the seam on the S-sleeve (the back seams if you have a sleeve in two pieces.
Sew the seam with running stitches or a sewing machine. Remember to fasten/lock all seams at the start and finish. Here 1 cm SA is shown. I prefer 1,5 cm to easy fell the seam and whip stitch it down.
Press the seams with an iron. If you use fine wool or silk, a damp pressing cloth (cotton cloth) can be used between iron and garment pieces to avoid pressing marks. In the photos below you can see the difference between a pressed and a new seam. Totally worth the effort!
When pressing: press the SA to both sides. Let it cool. Cut down one of the sides to half the width. Press the other SA over the cut one, pin down if necessary. This will create a sturdy seam when sewn down, saves you time and looks neat on the right side.
Pin and sew the other sleeve seam (if any). Press it the same way as the first seam. This is easiest with a sleeve ironing board, but if you don’t have any; press the seam with the sleeve laying flat on the board. Try to avoid creating folds in the sleeve with the iron.
seam on the inside of the sleeve
These photos show the technique with and without a sleeve ironing board
Gores:
This dress use 4 gores, one at the middle front, one back, and one in each side seam. The gores give you movement and a good drape to the skirt. On female garments I want the gores to start by the natural waist (where you are slimmest) to accentuate the curve of the hip and belly. On men’s garments, I start at the hip bone to give movement but no feminine curves.
Tip: When drafting your gores, do not make them into straight triangles, but make them slightly curved at the base. Like in this example: the gore should be 100 cm long, and as you can see the rectangle is just that, so the gore will be exactly 100 cm at the middle, but at the sides, you need to measure from the top and down, 100 cm, and that will be a bit shorter than to the line.
Why? To get the right measures, and a good shape at the bottom hem, as described in this picture:
The gores are cut at a diagonal/bias on the fabric. This means they tend to stretch more than the front and back pieces when pinning and sewing. To avoid this, work on a smooth surface and pin + sew the seams with the gore under the front/back piece. This is mainly a problem on a sewing machine with too much pressure on the presser, but also a good tip for hand sewing.
One gore has a seam in the middle to save fabric. Pin, sew and press this seam first. I like to place this gore in the back so it wont show, and to create symmetry in the dress. Then, cut the front and back center to be able to attach gores there. Make the cut line about two cm shorter than the gores; like this:
Start with the side gores, pinning them to the front. Sew them in place, and press both seams the same way you did with the sleeves.
Pin the front and back gores to the front/back pieces, right side to right side, one seam at a time. Sew it but leave the last 6-8 cm at the top. Repeat with the other seam, so you will have two gores with the tip lose. I prefer to make the tip by hand, from the right side of the garment
3 different ways to insert gores:
Press the seams you made, and press the SA on the front and back to either side of the slit, as if it was already done, from the wrong side. When reaching the end of the slit, the s.a will become narrower, and then disappear. Turn the piece and work from the right side. Pin the gore in the slit, so it lays flatly under the already pressed s.a of the front/back. Then sew it in place with a small whip stitch. With this method, you can check the gore to be sure it fits nicely, and it does not matter if it turns out a little bit too big; it will look perfect!
Another method is to sew the whole gore with this technic, if you sew your garment by hand. This is also historically accurate. Start with pressing down the s.a on the front and back slits, and then pin the gore along each side, and sew it from the right side using whip stitches. Press the s.a on the wrong side, and sew this down with whip stitches on the wrong side to, like when felling the seams in the sleeves.
If you only want to use the sewing machine, work on the inside of the garment, and continue with your sewing machine seam to the top of the gore, making the SA narrower as you go along the last 4-6 cm. If it is hard to see, fasten the seam, turn the gore up and sew it from the other side (still on the inside, just flip the garment from front/back to gore side). This might take a few tries before you get it right, just go slow and be prepared to rip the seam and try again if not satisfied.
When the gores in front and back are finished, sew the side seams; the side gores to the back piece and then the side seams (leave a hole for your arms for now. When all the gores are finished, remember to press all the seams!
Neckline:
I like to draft the neckline by hand for each garment, to be able to adjust it to each look I want. The secret is to try it on often, and just cut away a little at a time. You can choose between pinning, basting or sewing the shoulder seams before this. Make them the same way you did the other seams, but don’t press them yet.
Start with drafting a neckline, and armholes. Put the front and back on top of each other, mark the middle and draft a small neck-hole. Mine is 18 cm across, 9 on each side of the middle. Make it shallow, about 4 cm, just in order to try it on. You can then draft the shape and size of your neckline directly on your body in the shape you want (just put the dress on, inside out and draft in front of a mirror. Copy the side you liked best to the other side, left or right. The neck will probably just be cut down with some cm, depending on your size, while the front will be deeper. Remember to leave 1-1,5 cm SA; when you hem the neckline it will be a bit bigger than before.
Arm holes:
Making armholes is much easier if you already got a toile/mock-up to copy, but you can try this too: Put the dress on, inside out, and draft the armholes where your shoulder joint start, follow the curve at the front. Mark where the holes should meet at the side, as tight under the arm as possible. Do this at the back (ask a friend) or take the dress off and draft on a flat surface.
Now you should have a drafted line at front and back. Measure these ones, and compare them with the measure you took for your armhole in the beginning. Redo if necessary, the armhole should be a bit narrower than the sleeves (about 2-4 cm) in order to make a well-fitted sleeve. The front curve is deeper, and the back more shallow, but they should start and finish at roughly the same place on the shoulder seam and side seam. It does not matter if one line is a bit longer (front/back) than the other, as long as the circumference is correct.
This is the difference between the front and back of my dress. Note that I also cut down the shoulder seams to become a bit sloping. This is optional for you, if you have very sloping shoulders it will help you with the fit. If needed, do this before the shoulder seams are finished. Then sew the shoulder seams and press them.
Attaching the sleeves
The next step is to attach the sleeves, and I will be honest with you; it can be a bit tricky at first, so don’t give up if you have to rip the seam a couple of times before you get satisfied. The most important thing is to take the time to pin/baste the sleeve to the body and check it out. Don’t hurry!
You will have two sleeves, sewn together to tubes. Baste the sleeve cap (top curve of the sleeve) with loose running stitches.
If you want to check out how the fit is; baste the sleeves around the armholes, and try the dress on. Move around, stretch. Bulkiness at the front might be trimmed down a little. If the sleeve seems tight on top of the shoulder a bit more sleeve fabric might be moved upwards. Do not bother if the sleeve gets a little creased or has small folds, that will be possible to fit inside the armhole, that is what the basting is mainly for. When you think you have something:
Mark out the top of the sleeve (towards the shoulder seam) and the bottom (armpit on sleeve towards the side seam) with a marker or pin. Maybe there will be more sleeve on the back of your body, but that is just fine, you use it when reaching in front of you. Now you are ready to sew the sleeve into the dress!
This is a step-to-step on how to insert a sleeve in the armhole and make it fit. Use it as a guide if you felt unsure about the above: Turn the sleeves to the right side. Put the sleeves inside the inside out dress, and fit them into the armhole. They should lay right side to right side now.
Pin the sleeve marked shoulder – shoulder seam and marked armpit – side seam. Continue to pin the armpit, the part under the arm. Lay the fabrics smooth against each other, no folds.
The sleeve is a bit wider than the armhole, so it should make small waves, like in these pictures. This will be solved with the basting thread you sew on the sleeve. Gently pull them to gather the fabric of the sleeve a bit, in order to fit it inside the armhole. As the sleeve follow the arm hole curve better, pin it in place. The fabric should not make folds, but only gentle crinkles or waves. Adjust if you need. The basted and pulled together fabric should only be pinned to the upper half of the sleeve, never in the armpit.
When you have worked your way around the hole with pins and like the result, baste it in place with big running stitches. Make the other sleeve up in the same way, or try to make it the same… When satisfied; flip the dress to the right side, and try it on. Check the fit of the sleeves and your movement. A bit bulkiness around the armhole is ok, but there should not be folds or stretched fabric sections.
If it looks good, turn the dress back inside out, and sew the sleeves following the basting (with machine or backstitches). Then remove all the basting stitches.
To finish the seams, press them on a sleeve ironing board, or roll a bath towel firmly and put it inside the sleeve if you don’t have one. Press the SA down in each direction, then finish the seams like the ones before. I press them towards the body and whip stitch them down.
Wow, good job! Almost finished. Try the dress on again to adjust the length, hemline, sleeve hems and neckline if needed.
The sleeves should be a little too long when the arm is hanging, to fit nicely when you use your arms and bend the elbow. Check, mark any change you want to make, and do the same to the neckline.
Ask a friend to check the hemline of the dress so it looks even, mark a new hemline if needed. Remember to check the length with the correct shoes/belt since these can make a difference to how long the dress look. When satisfied, cut away any excess fabric and hem the dress. I prefer to fold the edge twice and whipstitch it down by hand. Remember that our SA for hemming was 2 cm. Thick wools only need a single fold before sewing.
Thats it! Now we have a nice dress, and you can use this tutorial for other garments as well.
Did you like this post? You can find a step-by-step video on a similar dress along with more guides and pattern on my Patreon. Join me there to help me make more tutorials!
This is my method for attaching pewter buttons to a garment. It is easy, simple and makes it doable to remove the pewter buttons before washing or to use on another garment, and then re-attaching them quick afterwards. Another great thing with this method is that you will not lose your buttons as easily as if you sew them onto the garment one by one, since you will have a secure ribbon to hold them in place.
Here is where I start; the sleeve at the top is finished, and the sleeve at the bottom already has its buttonholes and hems. You will need to make S-sleeves (with the seam at the back of the arm, going just over your elbow) and then fit them snugly over your underarm. I recommend doing a mock-up sleeve first in a cheap fabric to try it out. Do you notice the curved edge of the bottom sleeve? That will create room for the wrist and the start of the hand which are also inside the sleeve.
Start by marking out where to place the buttons, use a pen and compare with the already made buttonholes. Work on the inside of the sleeve. Depending on the size of your buttons you will need different seam allowances, I had small buttons and used 1 cm, but recommend that you use at least 1,5-2 cm.
Use an awl and make small holes in the fabric, for the buttons to go through. If you have a thin or sensitive fabric, you need to reinforce the sleeve before you begin, otherwise, the buttons may rip through the fabric when put under stress, such as moving or lifting when wearing the dress. A simple piece of fabric would do the trick, like on the sleeve above where the buttonholes have a strip of silk (sturdy linen is better to work with). Sew it into place before making the holes.
Do you see my trick now? I do not sew each button in place separately, but pull them through the holes I made with the awl. When I have them in the right place, I thread a sturdy ribbon (this one is in linen, but a braid, twisted linen threads or anything similar will go) through each buttons loop, to keep them in place.
The ribbon makes the buttons stay in place, and makes it impossible to lose them. Note that the ribbon is twisted from left to right to pass through each button from the same direction, this will give you a smoother seam later. The buttons are placed with the flatter side towards the sleeve.
When the whole set of buttons are attached and the ribbon threaded through them, fold the ribbon back, and leave a piece of it lying under the loops to keep it in place.
Final step! Fold the seam allowance over the buttons stem, loop and the ribbon, and whipstitch it in place. To remove the buttons, you will just have to rip the whip stitch open, remove the ribbon and take out the buttons to wash the dress in the machine, or use them elsewhere on another garment. To replace the buttons, repeat the steps above (the marking and holes should be left so you don’t have to redo them).
It takes me about 30 minutes to reset a sleeve, so quite doable instead of having to buy new buttons for each garment you make. This also works on bronze buttons of course, but fabric buttons I usually sew onto the garment one by one as is visible in finds from London (Dress Accessories 1150-1450). Also, note that you need the typical medieval button with its long stem, most modern buttons are flat and don’t work with this technique.
Today I just wanted to show you some of my new viking age glass beads that I bought this summer, and tell you a little about viking age beads!
There is plenty of finds from the viking age of glass beads of various colours and types. The most common way of wearing them seems to have been on a string between the tortoise brooches on a woman’s outfit, but the have also been found in necklaces, in small metal circles and loose in grave (also in men’s graves but I have no notion as to how many).
The world of viking era glass beads is big and interesting, but I am not an expert in any way. There are those who are though, and there is research going on about the subject. Glass beads were both imported by the hundreds and made in viking workshops, with different styles and quality from different geographical areas and time periods. This makes it possible to trace them back to their original area, and tell an estimated time they were created.
You can also find lots of free information on Historiska Museets database (The Swedish historical museum) and here is a search ready-made for you on viking age glass beads, with pictures on the finds; http://mis.historiska.se/mis/sok/resultat_foremal.asp
I like glass beads because they are one of few materials that withstand the turning of time and looks something like what they used to be, even after 1000 years in the earth. They are of course also pretty, and the handcrafting behind each bead are often outstanding.
I have tried to make some glass beads myself with the same technique used during the viking age, but with modern tools (such as gas, safety glasses and an oven for slower cooling) and find it difficult but very interesting. This summer I also, kind of accidentally, bought some beads from other makers, and now I have put everything together in new strings and necklaces for my outfit. These are not identical with specific finds, but more inspired by several different finds and graves. I will probably not keep everything, but they are so lovely I just had to experiment with them.
All the beads you’ll see in this post is handmade, by me and others. The blue-themed set will be used for festive occations I think, along with my new blue apron dress.
And for fun, this is one of the earliest strings of beads I made for my viking outfit. The photo is crap, half of the beads are modern, I used a thread that broke and didn’t know much about historical beads at all. Everything from this picture is sold or given away by now, but the brooches I still have and use since they are based on a find from the area of Sweden were I live.
Some time ago I made a medieval bathing dress in unbleached linen, and I wanted to share it with you. It is a simple project, perfect for an evening or if you want to practice hand sewing. There are plenty of bathing dresses in paintings from the late 14th to 16th century in Europe, they can also be seen in different cuts and models, and some are clearly supportive shifts that you could wear under your medieval clothing. Mine is very simple but with an intake under the bust to allow some support, but still being easy to get in and out from. No lacing is acquired.
Left; Bohemian, Codices vindobonenses 2759-2764 in the Osterreichischen Nationalbibliothek, in Vienna, Austria. Right: The Bathhouse Attendant, Bible of Wenceslaus IV. 1389.
This find is from A History of Costume, Kohler and is dated 14th century and described as a lady’s chemise or undergarment, the photo is old but you get the general idea.
Most of the pictures I have found seems to be dated to the late 14th to early 15th century, there are lots on the internet and I have a Pinterest folder on Medieval underwear so I won’t go into more historical sources today.
The cutting out; prewash your linen, fold in double in the length you would like, and then cut the A shape. I used the leftover fabric for gores in the sides (and at centre front + back if you like, it is optional) but this of course depends on your measures.
The first pictures show the general cut, the second the additional front and pack gores, the third the intake under the bust that give me the support. Do not take in too much, because then you won’t be able to get in and out of the dress.
About measures: The length of the dress measures from armpit to hem. The width is your measure around your bust divided in two (for front and back) add seam allowance but nothing more. Start the gores at your natural waist (if you are unsure, rather place them higher than lower) and pin the intake under your bust while wearing the dress with gores and side seams sewn/basted. Add shoulder straps last, mine is just double-folded linen cloth, whip stitched together and then fastened at the same position as I would have worn bra straps.
If you sew your dress by hand, use waxed linen thread and running stitches, and then fold the seam allowance to one side and whipstitch in place. This gives you a sturdy seam that is also quick to make. Hem the dress with running stitches or whip stitches, after your choice.
Making the dress in unbleached linen made it opaque even when it was wet, good for modesty. In artwork the dress seems to be white, may be visible nipples was a thing, or you would have to pick a very dense fabric. In some pictures, it is very clear that the fabric is transparent, but I chose the more sturdy and practical look. (update spring 2021: I have found that if you start with unbleached linen fabric, and sun bleach it yourself you will get an almost white fabric that is not as transparent as the modern bleached options in stores.)
The result? All considered, I am satisfied with the cut, sewing and look of the dress. It is also easy to swim in. Historically, being out in public in a bathing dress was not a thing, they can be seen on bathhouse attendants or in rare cases during the dressing/undressing at home or during dirty labour. Wearing it to the beach was certainly not a thing, but I liked to have a more historical dress instead of wearing a modern bikini when going for a swim at events.
There are plenty of bathing dresses in paintings from the late 14th to 16th century in Europe, they can also be seen in different cuts and models, and some are clearly supportive shifts that you could wear under your medieval clothing. Mine is very simple but with an intake under the bust to allow some support, but still being easy to get in and out from. No lacing is acquired.
