HANDCRAFTED HISTORY


4 Comments

Viking apron dress, part 2

Are you longing for that perfect iron age (viking) look of square awesomeness, yet still wanting to show off some womanly curves? Fear no more, this is how you make your apron dress fit really nicely! (Yes, we are going to be more serious real soon)

This apron dress is the same style as you can find in this tutorial, but back then I never guided you through the fitting, straps or stitching. Kind readers have asked for more details, so now this part 2 is here for you.

Ok, so let’s start with the dress already cut out and basted together (white machine thread). It looks something like this, hanging a bit boring…

Step one- try it on!

I pinned two pieces of ribbon onto the dress to be able to try it on easily. These will later be my guides for making the sewn linen straps.

In the back, I put the straps closer to the middle. I find them more comfortable and less likely to slip off my shoulders.

Now it is time to do some shaping! I like to wear my apron dresses higher up on my body, which means I get fabric bulk under my arms. To avoid that, I draft a curved line under my armpit and then cut away the excess fabric. You don’t have to make a full “arm hole”, just add some space for your arm.

Drafting the curved line in the armpit with a fabric marker.

The next step is to pin away fabric in the seam above the bust. Here the seam stood out a bit, so in order to follow the shape of my body, I pinned away a little fabric. As you can see in the photo it is not much, only to add a soft shape.

Marking the fitting with pins will allow you to feel the new fit.

Next are the side seams in the front. I pin away fabric under my bust, turn at my natural waist and continue out in a soft line to the basting line again. The goal is not to achieve a super snug fit, just to highlight that you have a body underneath.

Pinning the shape loosely.

Continue with the back seams and pin away fabric to add some shape to your waist here too. I hold my hand by my natural waist, and as you can see I did not aim to make the apron dress tight. Just removing a couple of cms to add shape.

My goal here was to be able to wear the apron dress with a woollen kirtle underneath, so I needed the fit to be loose. If you want a tighter fit you can try pinning away more fabric- just remember to try it on with new basting seams afterwards to make sure you can get it on and off. Apron dresses never have lacing or such.

Pinning the back seams by the waist.

Now it is time to check out the new fit! Mark the position of your pins on both sides of the seams, remove them to be able to take off your dress easily, and then bast along the drafted lines.

Basting can be done on a machine or by hand.

Here you can already see the added shape of the bust and waist, even without the seams properly finished. When you are satisfied with the fit, remove the old basting from places with double basting. This is needed to finish the dress by hand with a historical stitch.

Trying on the dress again to check the fit.

Press all seams with the basting still in place. (This step is important if you want to try out the seam below, but if you use a sewing machine for your dress you should first sew all seams on the machine, remove the basting thread and then press.)

Pressing the seam allowance to either side will make the sewing easier.
This is what the new shaping looks like after the pressing.
Sewing with wool thread.

Turn the apron dress so the right side is out (yes, we are sewing the dress from the outside) and start by the hem with a small whip stitch. Work your way up on the outside, fasten the thread on the inside of the garment as needed, and repeat with all four seams.

This is a sketch of how the seam looks, side to side with the actual seam.

The key to making this seam look neat is to make small stitches mainly running on the inside of the garment. I like to start from the bottom up, so I can try out the best thread tension and width between the stitches where it does not show so much. The pressing in the step before also helps a lot, as well as the basting on the inside, keeping the garment together while I sit comfortably on the sofa, sewing.

Close up on the seam. If you sew with wool thread, choose a thread with a high twist and 2-3 ply. Take shorter threads and a needle somewhat thicker than the thread. This will make the thread last longer when you work.

After the seams are closed on the outside, I remove the basting thread on the inside. Then I finish of the seams by cutting down the seam allowance on one side, and pressing the other seam allowance over this side. This way I just have to make one more whip-stitched seam for each long seam, instead of two.

Every seam is sewn two times with whip-stitching. This makes the seams sturdy and flexible!

Finish the dress with a double folded hem and whipstitches. Press all seams when you have finished.

When the dress is done, it is time to make some straps! Use the ribbons from earlier as your mockups /guides to decide how long your straps should be, but remember that the tortoise brooches will take some space too. Add seam allowance (3 cm) and extra for your loops. If you are unsure, make the strap 10 cm longer and then cut away the end you don’t need when you have made the loop and finished off everything else.

Linen fabric going to be apron dress straps.

The measure for my dress straps was approx 30 cm long and 4 cm wide. I made 2, and then 2 really short ones to make the loops attached to the apron dress above the front seams. Then I pressed the straps in the middle, folded them, and then folded in the edges. Very smooth!

Use waxed linen thread for sewing in linen fabric. Linen straps on wool dresses can be found in grave finds from the period.

Whipstitch the folded straps along the edge. When you have finished, press them again but with the seam in the middle. This way the stitching will be protected in the middle and the straps will be looking really nice and even.

Nice and even, I love pressing seams!
Making loops for the tortoise brooches.

To make the loop in the edge of the strap, finish the seam along the line and then fold the edge back and fasten it with some stitches. I like these loops, they keep the brooch in place and look neat. The small fabric pieces for the lower loops get treated in the same way. Double fold, press, whipstitch along the line and fold to a loop.

The loops are sewn to the inside of the upper hem, beside the front side seam.

Fasten the lower loops to the front, and remember to put them where you pinned your ribbons on in the beginning. The placement will help the shaping of the garment. If you wear a modern underwire bra, the placement of the loops is often towards the middle from the bra straps. Remember that your tortoise brooches should have a fairly even place to rest on your body.

Sewing the straps onto the back of the apron dress.

Before attaching the straps to the back, try the dress on with your tortoise brooches, to adjust the length needed for your straps. When you are satisfied, pin the straps in place on your back, and sew them with some waxed linen thread. I like to work my way around the strap and through the wool fabric to make them sturdy.

That’s it! We’re done with all the fitting and sewing, and owners of a splendid apron dress with a perfect fit! Did you like this post? Support me on Patreon to help me make more!